How To Properly Repair A Crack In A Swimming Pool

Although it'southward not a common occurrence, over your swimming puddle'due south lifetime information technology is possible your stride may crack. Luckily, repairing a croaky pool step is a fairly elementary process, and 1 you can exercise on your ain. Here, we break down the process of repairing cracks in pool steps, along with some useful photos of the procedure to help y'all along.

Materials Needed:

• a towel or hair dryer to dry out the pace completely (do caution with electric usage near h2o)
• a scraper or putty knife
• a rotary stone fleck
• 100-dust sandpaper
• fiberglass repair kit
• a dust mask (recommended, non required)
• masking record
• epoxy pigment, in the matching or desired color
• paint rollers for larger areas
• pigment brushes to cutting into smaller areas and edges

Step I: Remove Water

To repair your pool step you'll need your step to be clean and dry. This means draining your puddle water at minimum to a level below the part that needs to be repaired. For best results we recommend doing step repairs when you are doing a liner replacement.

Note: Practise non drain the pool completely unless you are doing a liner replacement. If y'all are non replacing your liner, only lower the h2o level far plenty that you can make the repair.

Step Two: Identify the Crevice

In the photo below you will meet the footstep has a crack which has been previously repaired, but is in need of a new repair.

Step Three: Clean and Prep

1. Offset, dry out the surface area to be repaired with a towel or hair dryer. It must be dry to the touch.
2. Using a scraper or putty knife, articulate off whatsoever major debris.
3. Using a rotary stone flake, grind out the cracked surface area from end to end.
4. Sand the area effectually the crack with 100-grit sandpaper until the fiberglass is dulled and the entire area effectually the scissure is smooth and level.
5. Make clean the area once again to remove any dust or leftover droppings.

Step Four: Apply Fiberglass Repair Kit

Directions for how to utilise your fiberglass repair kit may vary depending on the kit you apply. Exist sure to read and follow the instructions that come up with your repair kit. In our example we are using a repair kit with a mesh patch to ensure a strong, solid repair.

Stride 5: Sand and Polish

Once your fiberglass repair kit application has had ample time to cure and harden, sand and shine the repair. A simple canvas of sandpaper should do the trick here, though we as well recommend using a dust mask over your face then you don't breathe in any of the fiberglass grit while you work.

Once the repair is smooth to the bear on and even with the level of the existing steps, you are done sanding.

Step Six: Recoat / Repaint

In one case washed sanding, wipe the entire area with a dry towel to remove grit, droppings, and wet. Use masking tape if you need to protect any coping or liner edges near where you volition painting.

Using a pigment roller, apply the epoxy pigment evenly and use your paint brush to cut shut to the edges. Allow the beginning coat to dry out completely (4-eight hours on a clear 24-hour interval). Apply a second glaze. Since your pool needs to be filled every bit rapidly as possible if you are not replacing your liner at this fourth dimension, it is best to employ both coats of paint on the same day.

Allow paint to dry completely. Review the recommended dry time on your pigment can prior to refilling your puddle, (can take 4-7 days depending on weather condition). Once yous re-fill up the pool, balance your pool water ASAP in society to protect the fresh paint on your footstep. TIP: The pH needs to be in a higher place 7.4, and make certain your alkalinity is above 100 ppm.

We hope yous've constitute this helpful! If you take additional questions on this or anything else please cheque out our resources middle here or drop the states a comment beneath. Thank you!

Source: https://blog.royalswimmingpools.com/how-to-repair-cracks-in-pool-steps

Posted by: seidelbeimetch.blogspot.com

Share this post